Can I use a putty knife to scrape paint?

Do you push or pull a paint scraper?

You should.

When you need to scrape your walls with a brush in place of a squeegee you need something that is as strong and long-lasting as a good pry-bar. If you're using both paint scraper and paint brush you need the most reliable tool. For your first paint project, it's important to get the best tool.

I have a 2026 gallon homemade 5 stage system all my own design and I have been very pleased with its performance and reliability. My system is not that efficient though because I had to have 2 sprayer hoses as the last stage didn't have enough pressure on the sprayer. This led me to experiment with a few others methods. I tried a low profile can and it sucked the paint through like a squeegee. The last time I used my DIY low pressure 5 stage I achieved up to 40-45% more efficiency than before. I put a hose in line from the tank to the first nozzle (the large opening one) then I added another smaller 3/8" tube in line with the first. This is much easier to clean out the solids than running the cleaner hose under the whole line. I then add 3 more low pressure nozzles. In this way I get better performance than using a paint scraper. When you use 5 stages you're cleaning the paint solids from a large volume of paint and only going to get the paint closer to its "perfection point" if you take as little paint as possible and go to a low pressure sprayer but this also leads to a lot less pressure on the surface being sprayed which means better quality paint and smoother finish. It also helps that I paint ceilings, so my first two stages are for scraping the ceiling properly and then removing the debris. The third and fourth stage are for applying primer/mildew control, while the fifth stage is again for doing only ceiling, it's a big time saver. I know for sure now how much I'll use. I never had it this efficient before.

Even though many believe that oil-based paints are environmentally friendlier, it is still recommended that you seal your walls before painting them. Sealers are a two-part mixture (sealer and topcoat), which can make the difference between your walls lasting a lifetime, or cracking after 2 years.

Can I use a putty knife to scrape paint?

Hey everyone, I'm kind of new to DIY so pardon the ridiculousness of my questions!

I bought a house earlier this month and I was hired to do a few paint jobs. It's an old house and I can't wait to change everything up from the outside. So I'm doing the house from top to bottom.

One thing I'm really curious about is how to remove the paint from an old (probably 40 years old?) window frame. It has no sill and isn't completely closed off so it has a nice gap of maybe 1/2". The paint in that area is cracked and peeling. I'm not sure if I'll need a primer, but before I paint, I want to be able to sand the frame and scrape the paint out.

I was thinking about using a putty knife to scrape it up, but I can't see how I'll be able to get all of the paint out. If you could please help I would really appreciate it.

Re: ? If you can get the corners out of the frame that would probably work the best. As far as scraping go check with a paint store, they should know best for you though. A scraper could work well but you might also want to take the frame down (assuming it won't fall apart).

Also, if it's a really old place I would be leery of the putty knife/scraping route. Thanks for the input guys! I was just about to do a test patch in the floor to see what was best. I'm assuming the more I scrape it the better, since I'll need to remove large amounts of the frame? What I'm wondering though is, how does the frame react to solvents? I've heard that some things could weaken the frame when exposed to certain solvents (cabinet glue comes to mind) and you're probably not scraping it away from your house when you scrape it. So, should I go ahead and risk it, or should I not use any kind of solvent at all and just wait till the framing is removed?

What is the best scraper to remove paint from windows?

I have read about the best of and the worst.

I am looking for a simple, do-it-yourself project that will remove a good amount of light green paint from a windows frame using my hand and a scraper.

Answer:I have used and I still have some in my workshop. In all cases I use scrapers on a piece of ply with sandpaper to help remove the paint.

Best Answer:I do it all the time. It is a nice easy project and your local paint store can also help, they might even be able to get it done for you. It could be as simple as removing the color off the window in a pinch.

Or if you need it cleaned better and then repainted the rest of the house you can get someone who knows what they are doing, like your painter. Answered by Anonymous on 4/5/2013 9:35 AM. Answer:Yes, it works I just did a full size boat and window so its easy to work out. The problem I had was the paint was on the inside too so I found with spray primer and a scraper it's good enough. There is no glue to break down.

If your frame has a flat side it may work but I find it easier and faster to remove paint with sand paper and scraper. Make sure to get a scraper with a soft tailed edge that doesn't snag up the frame or walls etc.if you are lucky you may have a couple old ones laying around the house to borrow from. You can also pick up scrapers at lowes or home depot for a good price.

I have also used scrapers on windows before. These may not help, but you need one anyway! Good luck. I have been using this same method for over 20 years to remove paint on windows, etc. Its a good and cheap alternative to hiring a painter. Also helps you sleep easier at night (or during a long day's carpool)

I would try using rubbing compound instead. I have some on my windows and its pretty decent. You may even be able to use it from auto paint shop.

Do paint scrapers work?

I'm looking for a good paint scraper.

I don't want to buy a whole set of expensive tools, just one tool that will do the job.

I'm not looking for something that's going to work in 20 years, so I'm not looking for a cheap one. I'm looking for one that is going to last me for the next 10 years. I have a small garage and I'm not going to be moving big stuff around very often. I don't want to spend a lot on a tool that's going to get damaged easily or not work well, so I'm looking for something that will do the job well.

I've used a set of metal ones from Home Depot before, but they were too cheap to be worth the money. Is there anything out there that can do the job? What are your thoughts? Are the ones from Home Depot worth it? Are they cheap because they're not made out of real steel or what? A set of stainless steel scrapers with wooden handles, and a set of metal scrapers with wooden handles. And since I'm being told I should get a set of all of them, I also want a set of the ones with the aluminum handle. But if those ones are any good, I don't need the other ones.

Re: ? Stainless steel is not rustproof. If the plastic handles are not durable, they will peel off.

The wooden handles on the metal scrapers are there for stability. As long as the handles are attached securely to the scraper, they should last longer.

As far as the metal scraper, the aluminum ones should be the best. They are stronger and they're less expensive.

I bought a set of scrapers. I didn't know there were different types of scrapers. I figured they'd all work the same.

The one I got was stainless steel.00. There was a set of wooden handles, and there was another set with aluminum handles. The plastic handles came with the metal ones.