What is IP domain name command in Cisco?

How to look up domain to IP command line?

How do I see the IP of a website from the command line?

I need to check this every now and again. Note that I don't mean the "site's homepage URL" which is - I want the IP that IIS has for the server. I don't think there is a dedicated tool to do that; if it were I'm sure I'd have stumbled across it by now. You may then use that IP to connect to your HTTP-server.example com
Mail.lan has address 204.5.196.19
Mail.lan has address 65.52.23.5
Mail.lan has address 10.102.45.19 80
Trying 204. Connected to noc. GET / HTTP/1.0 200 OK Date: Sat, 26 Oct 2026 14:48:33 GMT. Server: Microsoft-IIS/6.0 X-Powered-By: ASP.NET
You may want to set up some iptables rules so that your server only listens on specified port(s) on external addresses or whatever is appropriate for you. Edit. You can actually also use ping in your case, as the host is reachable and you can ping it with PING www.com: PING www.com (204.19): 56 data bytes
64 bytes from 204.19: icmpreq=1 ttl=255 time=0.093 ms
64 bytes from 204.19: icmpreq=2 ttl=255 time=0.075 ms

What is IP domain name command in Cisco?

Cisco IP domain name command is used to configure IP domain name for IP.

Cisco does not support direct configuration of IP addresses, but only IP address that is derived from a domain name by a special convention (called ip domain name command in Cisco). The ip domain name command is used to assign IP address from domain name. Some commands, such as address family and IP address are used together with the ip domain name command to assign multiple IP addresses for a single domain name. However, other commands, such as subnet mask, are used solely for their default values. The ip domain name command does not operate independently. It functions as one of the other commands. To work together with other commands, see these examples:

Syntax Description. A network host name or a classless routable IP address assigned to a specific interface. A host name can have spaces and special characters. Use quotes around a host name to avoid interpretation of those characters in a router configuration file. Classless routes are the most secure and useful in Internet communications because they reduce the number of router configurations required to cover a large number of computers and routers. For example, an administrator needs to configure a static route to a new site with 100 hosts. Instead of configuring routing for each host, he configures one routing entry for that IP network with a netmask (classful routing). That entry covers all of the hosts with a single route. A prefix of length 256 means 128 bits of the route contain a network ID, the next 28 bits contain a subnet, and the last 14 bits contain an interface. See interface(config) for a description of interface numbers, which must be unique on each interface, and interface groups.

Command Default. The device ignores any command parameters not listed in the table. Command Modes. Expected Use Cases. Use cases for this command include: Enter interface numbers as shown below; this command does not work with interface group configuration. Command History. Release. Modification. V11.2(33)SXE This command was introduced. Usage Guidelines. Examples. The following example assigns an address for host web.exampleserver.com to interface vlan 7.

How to find domain name from IP command?

If I am trying to find an IP of any given domain, how can I do this?

For eg: if the website is , I would like to know it's IP address or find out an IP by . And what command should I type in to get this information? I am using ubuntu.com ; <<>> DiG 9.10.3-P1-Ubuntu <<>> google.com
Google.com ;; QUESTION SECTION: ;google. IN A ;; ANSWER SECTION: google. 1167 IN A 194.109.27.177
If your ip is dynamic then gethostbyaddr("185.100.45.100") should return hostname.

Try this code.> output: stackoverflow.