What is the difference between OpenVPN site-to-site and client server?

What is needed for site-to-site VPN?

I know I could use a PPP connection if all that is necessary is for multiple users to be able to get on the same subnet as a specific internet gateway, but would this be the only requirement?

To be able to do that do you need an external IP address as well? I'm assuming there's something else I need? I've been googling for this and haven't come across anything helpful or even applicable. You mean they can share their resources as the same gateway? In theory, that makes sense. And just wondering, what happens when one user takes too much bandwidth? Does that affect the site-to-site VPN connection or do all of them use the same bandwidth? We have several people on our network who use a lot of disk space. We have configured VPN tunnels between two of the data centers to allow them to move files from one location to another when their disk starts running full.

They each pay for their own bandwidth, but we do charge for the bandwidth of the tunnel to the destination (which is at the other end of the tunnel). If were not charging for that, it would be much less expensive to have the data transfer between these two locations happen in bulk than having lots of people access these machines remotely all over the clock.

Just to add to this question. I have never had to do a site-to-site VPN connection before, and I have never used any type of VPN. What do you have to do to setup this and make it secure? Do you run a Windows server on a server in the other location, then setup a virtual router or something and have it route traffic through the site to site VPN? How do you set up the VPN through the routers? Do you have to set up a separate computer for the site-to-site VPN connection?

If you're trying to ask how many routers/NAT boxes that are involved in this setup, we're assuming a single network that is connected to a common gateway/Internet provider.

Can OpenVPN be used for site-to-site VPN?

Question:Is it possible to use OpenVPN on a site-to-site network?

Answer: Yes, of course. Any IPSec VPN protocol can be used on a site-to-site configuration.

Example Configuration: # The following example is taken from the OpenVPN installation page.# This configuration was tested on a local LAN.# OpenVPN is able to make connections between two networks.# If you want OpenVPN to act as a gateway between your routers# then you will need to have two subnets # each on different broadcast domains.clientport 1194secret mysecretkey # The IP address and port of the remote server# on the remote side (which will also serve as the DHCP# server)remote 192.168.1port 9443server# Do NOT set "dev tun", since the # device type ("tun") is selected by the user.# On Linux, keep this line as is.

What is the difference between OpenVPN site-to-site and client server?

OpenVPN site-to-site is for connecting a server to another server.

OpenVPN client/server is for connecting a client to another client or server, or even connecting one client to one server. In short, OpenVPN site-to-site is basically "server-to-server", while OpenVPN client/server is "client-to-client" or "client-to-server". The two differ in that a site-to-site connection does not include a dynamic server, while a client/server connection does include one. An example of a site-to-site configuration would be this: -redirect-gateway def1. -redirect-gateway def2. Whereas a client/server configuration would be this: These are two very different configurations.

How to setup site 2 site VPN?

I have a new setup, and I need to connect two remote networks together, across the internet. Both sites are Windows 2025 servers, using IIS 7. I have two sites, both of which have to be able to talk to each other. How do I accomplish this? On one of the sites, we have our ecommerce site. On the other site, we have an internal network that I'd like to connect to the ecommerce site, using a VPN connection. The VPN connection will between the two sites.

On the ecommerce site, we'd like to have a button that says "I'm now connected to the internal network". We'd like the button to appear, when the connection is complete. I'm not sure if this is possible. What kind of VPN would best? Would IPSec or L2TP work? Or is there something better? 2 Answers.
There are two things you need to do: You need to install a VPN client on the server that needs to connect to the other server. You can use OpenVPN, PPTP, IPSec, or L2TP/IPsec for this.

You need to configure the server where you want to connect to as a gateway. It needs to be configured as an Access List in Cisco IOS, which means you need to go into Advanced IP Services and choose Access List. Make sure that it is enabled (the default is no) and configure the IP address that you want to use as the gateway.

Now, for the client, you need to download a VPN client from the vendor's website and run it on the server that needs to connect. You will have to enter the IP address of the server that needs to connect.

Once you do this, the button on the client should appear when the connection is complete. In my experience, PPTP works fine. You can use any VPN protocol you want, it just needs to be open source.